Tool belt suspender is a harness to support your tool belt against your back and chest. While the belt might bulk up and weigh down on your waist especially if your work requires you to crawl up and down on a construction site or climb up a ladder. A tool belt suspender would distribute the all overweight on your shoulder and back so you don’t have an unraveling pressure on your belt.
Definition: What Is Tool Belt Suspender
Tool belt suspender is a padded strap that holds the tool belt to your waist by distributing the overall weight on your shoulder, chest, and back. Since your tool belt will carry gears that are of heavyweight, the waist alone cannot take on the weight, it just might pull your pant down!
So the tool belt suspender is here to save the day.
Why the Professional Use Tool Belt Suspenders
When you put on your tool belt to work on your job and put the gears on, they are heavily loaded, you might not feel uncomfortable for a short while, but imagine working all day with such mass on your waist that is directly making an impact on your spine, and your spine alone.
That comes with some backache at the end of the day, then had to carry the load all day for an extended period of time. The best tool belt suspender saves you from such labor. Not to mention they give you a great look, provides you with a straight posture, thus giving you the smartness your overall appearance. So, you do not have to hunch back to maintain the weight on your waist.
Then there is the problem of the tool belt moving from a place, let’s face it with the overloaded belt with tools and you walking and moving the tool belt sometimes rotates from its place.
Wearing a tool belt that is loaded with heavy-duty equipment and depending on your work type you may need to climb up a ladder to fix or install electronic equipment, or crawl up and down to fix pipes if you are a plumber, and a job on the construction site demands a more secure placement of your tool and your personal comfort to move up and about.
Not to mention your safety, a tool belt imposes a certain threat when climbing up a ladder with the loaded tool belt only hanging by your waist that imposes a certain danger due to the imbalance of weight.
Tool belt suspender diffuses the weight all over your upper body, so you do not feel the overly heavy load on your spine and waist. Getting a tool belt suspender would save you from that harassment and danger.
Buying Guide Buy Tool Belt Suspenders
Look for a few features in general that play a big role in tool belt suspender and your comfort in overall weight bearing. The key features are noted below.
- See how it attaches to the tool belt, some are only hooks and hoops, whereas some are clips. The hooks and hoops may fall out if you are climbing on an inclined space. So choose wisely
- Check how thick the pads are. You do not want to stress your shoulder and chest from carrying the weight.
- Does it fit you well? This is an important issue, you do not want something so loose that sags and you have to end up dragging it around.
- Check the pockets, how is the stitching, the sizes of the pockets. Does it suit to your specific need? If you need various sizes of screwdrivers, you need more pockets for screwdrivers. If you need o use tape constantly, you need a tape holder.
You may also like to read guide to buy the best electricians tool belt and best carpenters tool belt.
Selecting the Best Tool Belt Suspender
The tool belt suspenders come with various features as well, some are padded and some are not. Some are well ventilated, with pockets and pouches while others may be simple. The suspenders come in different sizes as well. The belts may be adjustable in some suspenders.
We review some of the best tool suspenders available in the market and discuss their ups and downs.
1. Tool belt suspender by SpeedSquare Tools
SpeedSquare tool belt suspenders are fully adjustable belt loop has padded back and shoulder, it has a phone pocket. The chest strap is available and adjustable. It is made from 1680 denier nylon.
It is usually well fit for someone up to 5’7/8” for someone taller than 6 feet they might need to extend the suspender. A point worth mentioning is that the loops are not included when you buy the suspender. So don’t forget the loops, remember to buy them at the same time. It becomes easier to install with the tool belt if you use the Velcro loops.
The suspender is quite adjustable and the pouch for phone easily fits a mobile phone securely.
The downside of this bag is that the padding is minimal, it only covers the shoulder and the back and chest. Not to mention the padding is not that heavy duty. The phone pouch is also outdated in size; it won’t hold today’s big screen phones. Depending on your height those shoulder pocket may be too high to be usable. Tall persons might find this product uncomfortable.
2. Occidental Leather 5055 Stronghold Suspension System
As the name suggests, occidental 5055 tool belts are made of leather, the shoulder straps are padded and the leather is of good quality. The leather loops can accommodate up to a 3” belt, the loops are closed out by the rivet. The padded shoulder straps are made of nylon. So no worries about making the harness sweaty since nylon are water resistant.
If you want the loops around the belts you should notice as mentioned earlier they are closed by rivets, that is it comes pre-riveted, but you can always drill them out to use Chicago screw.
The hooks of the belt face outwards, so they might get a bit hooked up with the other things. There is no extra pouch attached though there are some small, narrow pockets you might keep a pen or small screwdrivers.
The anchor points are not fixed so as you move around the tool belt also moves around which can be of great discomfort since the loops do not fixate at a constant point on the tool belt. The padded support on the shoulder also moves and is fidgety since the hoops are not fixated, the buckle side won’t stay put sometimes.
The described discomfort with the loops can be omitted by adding some anchor points on both front and back. This is not even a problem if you are someone who carries massive weight on the waist, then no adjustments are even required, they will stay in place.
Since the overall build is very well, especially the quality of the shoulder rigs and the belt is very stronghold and can sustain a rough kind of use. The chest strap is amazing, keeps up in place. The craftsmanship is well appreciated for this bag.
3.ToughBuilt – Padded Suspenders
The width of Padded suspenders by ToughBuild belt is about 2 Inch, the suspender has four hooks and loops. The two front rings are adjustable Velcro straps. The hooks and clips that consist of the suspender are made of die-cast, the two die-cast part of the clip is flared in the middle to make it hold together.
The holes around the belt tab do not have a protective layer around, though the suspender is heavy built and really durable the belt holes might fray away with prolonged use. The clips holding the pouches are about half and an inch in width, hence the weight is a bit concentrated there. Instead of the width is as wide as the pouch is the clips are not broad. There are no pencil holders and nail sets. The plastic latches should hold up for a while.
The detachable feature is appreciable; since the setup is customizable you can adjust each strap according to the mass you loaded on it.
It has multiple attachment points, so from any angle, you put on, you can attach it to your belt. The clips and hoops in this Toughbuilt tool belt, however, are made of die-cast. Cannot vouch for them since they have been criticized for breaking after a use over a lengthy period. Though the Velcro is of great quality and does not separate easily, adheres strongly and holds.
4. McGuire-Nicholas BL-30289 Gelfoam Suspenders
McGuire-Nicholas BL-30289 Suspender paddings are made of gelfoam, it is a compressed gel-like foam, this foam does not constrict perspiration and dampen the fabric instead it is breathable. Though it says it has a pocket for your mobile, in reality, it hardly accommodates a flip phone, let alone a wide touchscreen phone that we use nowadays.
The straps of this suspenders that are to be attached to the toolbelt are metallic. The web straps on these do not stretch much. The metal claps are not heavily built and are brittle, a big amount of weight and prolonged use may wear them out.
The clips are really not rigid enough to hold the weight. The main objective of a tool belt suspender is to hold the tool belt in place without any hustle. Though the zip ties make up for the crappy metal claps still they are a drag. The clips also don’t hold in place whenever you bend over with weight on your tool belt the clips release the bags. Sometimes they unclip and release the tool belt.
Not having a quality metal parts is the only downside of this suspender. These suspenders provide comfort over your neck, shoulder, and back. The buckles are heavy built and quite adjustable in nature. The overall bag is quite adjustable to variable heights.
5. Tool Belt Suspenders by Tradegear
This tool belt suspender by Tradegear has a cross over the leather divider, it is made of nylon, the straps over the shoulder are of two inches in width and fully padded. The suspender does not weigh much, but it is made of one of the most durable materials, the nylons on the straps and the leather made belts.
The metal clips are sturdy, very well built and can sustain a large load. These suspenders are very much comfortable to use. Unlike other suspenders in the market, these have the feature of a crossover belt so the weight is distributed all over your back and chest not just on the sides.
They sometimes keep unlatching at hooks, when they are set down. The nickel plated locks that attach the suspender to the toolbelt are of high quality, strong and holds their position well.
How to Wear Suspenders with Tool Belt
Wearing a tool belt would become comfortable less stressing on your body if you wear the tool belt suspender, but not wearing it properly could also result in back pain so wearing it with proper discretion is of utter importance.
The suspenders should wrap up your back and shoulder and carried to your chest and clip it around your front on the waist, the tool belt should not be hanging or sagging from the suspender instead it should be well fit. And do keep the tool belt empty before installing the suspender and then load it after securing the tool belt with the suspender.
When you climb or work in inclination you can turn pouches away from your from and leave them on your back.
Frequently Asked Questions
Q. Would these create friction on the shoulder while working?
Ans. If they fit you well enough they should not, but if you have to work overhead for a long duration your shoulders may ache depending on the padding of the tool belt suspender.
Q. Does all of the tool belt suspenders have loops attached?
Ans. Some do, while others do not, for example, the suspender from Speed Square tools do not include loops, you either have to make them or them beforehand.
Q. Would these tool belt suspender fit any size/What is the max size for these suspenders?
Ans. They are usually very adjustable, but someone with height above 6’5” or below 5’ should check carefully from the manufacturer’s description, because sometimes they might not be adjustable to their size. If they choose a suspender that is maybe with a leather belt and you can create an extra hinging point that would be preferable.
A tool belt accentuates your workflow, but a heavy tool belt comprised of too many heavy tools might just make you hunched over, be hunched over too much and you put pressure on your back. The best tool belt would save your waist from strain and pressure and distribute the weight of your tool belt all over your upper body. So, just opt for a tool belt suspender, not just any tool belt suspender the best tool belt suspender that suits you. Wear your tools with comfort and style.