Electricians do such a wide variety of jobs, wiring a total household while construction, fan and light installation, generator or IPS installation, PS repairing and so on. The environment on the job is unpredictable, maybe it is a construction site, and maybe you are in a home repairing stuff. Sometimes you need to make a vertical climb; taking the essentials with you on a first climb can be done by buying the best tool belt.
Why Electricians Need a Tool Belt
To be an electrician is to work constantly with the most elegant and complex of the tools. There are wrenches, wire strippers, vise grips, torpedo levers, screwdrivers, nut drivers, pencils, a knife, electrical tape, cable cutters, some tools we just use constantly, think about working in an environment, where you are working on your eye level or chest level and can’t afford to keep your tool at that same level, so every time you need something you have to bend over.
Sounds exhausting, right? Keeping a tool belt on your waist could relieve you of this hurdle. The best tool belt could contain all your sensitive tools with care. The tool belt could sustain a bit rough handling.
Choosing the Best Tool Belt for Electricians: The Checkbox
Before you go on and buy yourself the best tool belt just make sure they go by your requirement, certain parameters that better be checked before the order placement.
The material that it is made of is of utter importance, they are usually made of nylon, polyester, and leather. Sometimes they come in with plastic linings to give the bag a proper shape. More will be discussed in detail in further study.
The tool belts come in various size, so do check them before you buy. You do not want to buy a one that is more lose than your waist since you will be carrying weight, it will sag more than usual. So check that measurement very well.
An adjustable belt is always more comfortable; you could tighten or loosen it up according to your need. The elastic ones are not that reliable since the gears you carry around are heavy in weight they eventually lose elasticity.
The number of pouches or compartment determines how much items you can carry compartmentalized
The hoops are of great for tool belt you can carry the bigger items like the hammers, pliers sometimes the drills.
For carrying the little items like the screws and nuts of different sizes you at least need one zippered compartment so check that out.
Understanding Tool Belt Materials
The most common and traditional materials that are at the same time most durable are the one’s Leather, canvas, and nylon. The durability depends on the material, of course, there is the quality of stitches and other things to consider but since the accessories that you carry are sometimes of the jagged end and heavy in nature the durability is what we want in the end.
Leather: The Most Comfortable with Durability
Original leather goes through a lot of processing from the beginning, the air drying or salt drying process, the tanning process. The most modern tanning processes include chromium salt processing; previously it was done by oil. So there are various types of leather. There is original leather; the artificial one. Though leather is all great as the material of choice for your best tool belt. It is not water resistant since water degrades leather, damp weather is an enemy to the leather products.it is easily scared if you are working in a rough environment or climbing the wire.
This is a synthetic fabric and it cuts down the manufacturing cost, it is a water resistant element so good for a damp weather, though this fiber may carry a certain load, a more tremendous type of load may rip them apart especially the compartments within. The polyester being a synthetic fiber is less expensive in comparison with the leather, though it has a dye migration problem that comes with prolonged use. It is strong and flexible as a material, resists water as well as wrinkles and shrinking. It might stick to your skin if you are sweating.
Nylon is a synthetic fabric such as polyester, it costs almost as much as the polyester one, but more durable in nature and less water resistant like the polyester. But yet a better water resistant material than leather. Nylon is really resistive to corrosion that means it might not leave as many scratches while you crawl up with your things in your toolbelt. So it offers a great deal of insulation. Nylon attracts water molecules though it resists passing through damp weather might swell up the material.
What Are the Best Electrician Tool Belts?
The best tool belt would be the one that can contain all of your tools and gears and the sensitive pieces. Your workplace can vary in weather and environment. So containment is one thing but securing the gears to their places is another thing of vital importance.
While utility can enhance an electrician’s professional life, wearing the belt with comfort, seeing if it fits to match your level of comfort is yet another parameter to match. When you have loaded all your gears, does the toolbelt fit on your waist?
1. TradeGear LARGE 36-40″ Electrician’s Belt
The TradeGrear tool belt comes in various sizes to fit on all sizes of waist. In waist size, the size range around the waist is of 30 to 35”. There are three small pockets, two are large and contains strap-on, so they are all good to go with a hammer since it is a snap on and off the strap. It is well suited and good for larger tools as well. There is a loop where you can leave an electrical tape on, the yellow loop. The loops are big enough for an electrical tape. The trad gear is usually made of 1250 denier of nylon as the base material. The bottom forms a flat shape so the pockets are sturdy and well formed.
This pouch is very well suited to an arduous work environment. This tool belt is suitable even for crawling under a sink, or a construction site. It can easily carry the primary tools like wrenches, wire strippers, screwdrivers, knife, cable or wire cutters, driver sockets, pencils, folding knife, electrical tape.
The metal clip on the back is a strong feature; you can put your belt through it to secure more attachment of the pouch to your body. The base of the pouch is sturdy enough for it to stand up on its own.
2. TradeGear LARGE 36-40″ Electrician’s Belt & Bag Combo
This tool belt has an excellent design, well-thought pockets that come in handy for carrying a lot of gears. The handles are well padded
It has 27 pockets of varying size, the ultimate container for your tools. Anything you might want, name it, there are enough pocket and holders for your tools.
There are five different sizes to this bag. As mentioned before the trade gear is usually made of 1250 denier nylon, hence it does not conform to the shapes of the tools like the leather ones. The nylon material as you know is an inelastic and a rigid material of somewhat, it is easier to keep it wide open while working because of its rigidity. Since it is leather made so it molds to whatever you place inside.
The Velcro that places the pouch on the belt has some shredding issues. But the overall construction which is very practical in nature is really noteworthy.
3. Occidental Leather 5590 LG Commercial Electrician’s Set
Occidental Leather is one of the best tool carrier manufacturers in the world. It has 37 compartmentalized pockets. It is made of finest leathers, it is made from the top grain leather, though it should be mentioned that most pockets are made of nylons.
The leather is more durable than nylon, though it might take a few days to soften it up, use of a leather conditioner will solve this problem and help them mold according to the equipment you place in them. The belt and one of the pouches are made of this leather of description. The larger of the pouches are made of nylon, which is more suitable though less durable in some cases for holding your tools since some of them might pierce or damage the material in a different way with the jagged edge.
Philips screwdrivers, flathead screwdriver, diagonal cutters, lineman pliers, strippers, a couple of small screwdrivers, folding knife, and a marker, a small drill is easily portable as well. The hammer loop and one tool pouch is made of leather.
4. McGuire-Nicholas 804 The Organizer Mini Work Organizer
The estimated measurement of this tool belt and its pouch is it is about 6 ” wide and 2.5″ deep and 12″ tall.
This tool belt has two large pockets, three small pockets, a loop for measuring tapes. There is a small plastic pocket inside the main pocket that comes in handy. The pockets are large enough to carry an iPad. The main pocket is about six inches deep. It has a hook that you can slide unto your pants, pretty handy on that note. You can also clip it up, so it reduces a lot of your work. A relief for your spine since there is no need for that much bending over.
Though the material outside is strong, However, the material dividing the pockets are not of good quality, it is thin, there is a chance of tearing if you load up some heavy tools. It works out with all the tools, so the separation is thin and unworthy.
The absolute profound part of this tool belt is that it has a hook that can slide into your belt or pocket and even pants. One pocket only with elastic for holding up your item, so might accidentally fall out The number of pockets is not sufficient, hence not many different slots for tools not to mention the pocket with elastic band though great for keeping tools in, not great for keeping the heavy tools, because the elastic is not tight enough to hold these heavy tools. The nylon strap is provided for your tape, not a metal one, so for someone with the intense use of the measuring tape not so great at holding the tape. This tool belt just does not specialize in tool carrying as much. It is not that compartmentalized so you cannot accessorize your tools.
5. Gatorback B240 Electrician’s Combo
This belt has a dashing outlook. The tool belt is heavy made, very sturdy and well formed in nature. Every product by Gatorback has a one year guarantee for a defect-free year. It is made of 1250 Duratek Nylon. This pouch contains 18 pockets with a tape chain too. The bag is a solid one and the layout of the pockets are good looking and provides get service. The pockets are durable with plastic lining, so they do not sag and looks smart. It is a nylon made belt that has leather tips at the belt holes.
There are open pockets for screwdrivers and wrenches. These are very sturdy and really well made despite the fact that these stay open bags. The material does not weigh much on its own, so that is a relief. The tape holder does not easily make the tape latch-up quick, but you can make it work. There has been a complaint on the right side pocket Velcro tearing up a bit (though the belt holds it up) after a long use. The Velcro could have been better, both in strength and width but it works and sticks to the belt.
Since the pockets are rigid in nature they do not conform to your gears shape and size, so you cannot just push something bigger than the pockets and hope they would just stretch.
The belt is heavily padded, very comfortable this one is the proof the tool belt, the cons would be the Velcro as mentioned. Though the bag is a solid one, it won’t sit up when putting on the ground.
6. NoCry Heavy Duty Canvas Tool Pouch
This is a 600D canvas made the backpack with 7 pockets and 10 loops. The bag is of durable material, easily washable. The loops enable us to carry the hoppers, heavy duty wrenches, and screwdrivers easily. This tool belt contains the body of canvas whereas belt is made of nylon.
The loops come in handy, you can just put your hammer there then just pull it out at your convenience. The belt is adjustable to your waist also can be hung from your belt. A special feature of this bag would be the metal loop on the front decorated with rivets that help you hang a measuring tape as well as other tools. The belt is adjustable to 28 to 52 inches. There is a smart metal on one side of the bag, the loop on another side is really good and comes in handy, and you could hang a hammer or a heavy duty plier on the side.
This tool belt is great for carrying big items since it does not have any zippers on the main pockets, also have a careful look after the items since they are out in the open.
A noteworthy fact is that if you need to take a vertical climb or work at an inclined job site, this is not the tool belt for you. It is lightweight but does not have a rigid part at the bottom, so it won’t sit up straight when you put it on the ground. Also if you notice, the pouch will occupy only one side of your belt, so the weight will only be at your one side. Consider this before buying whether you are comfortable with it or not.
7. Milwaukee 48-22-8110 Electricians Work Belt
This is a good quality bag that designed to be of the compact in nature, the pockets are compact and yet of heavy design. The pockets have plastic linings so they keep up in shape even with the tools loaded. These tool belts have a flat bottom so they stay put both on your waist and ground.
This tool belt is made sturdy enough to contain some sharp gears within it. It will be fit for a waist size ranging from 30 to 52 inches. The pockets are good for carrying screwdrivers and pliers but since they are small in size they are not that great for carrying gears heavier. The bag is light in a superb way but the pockets hold up their formation since there are plastic bottoms inside of them.
There is a clip for the tape holder. The integrated back support is most comfortable; it distributes the weight so you do not feel pressure. The hammer holster and pockets do not sag, they stay put in their places. There is a pocket big enough to hold a speed square. The bag folds up so nicely and compacts that you can put it into the tool backpack.
How to Wear Tool Belts in the Right Way
After buying a tool belt you want to make sure you get the best out of it, right? So we need to put it on properly so it does not sag, or so you can find your tools easily if used in the right way it becomes a helping hand and as an electrician you need to get all the help.
So here is some step by step procedure to put on your tool belt.
Empty the pockets
Do not put your tools in your pocket before you put the belt on, it will misfit, and also you’ll have a hard time buckling the tool belt.
Most used tools at your dominant side
Maybe you need the screwdriver frequently, so it would be more fitting to place it on the side of your dominant hand, if you are right handed place the essential gears on your right side, if you are the left-handed place the most used tools on your side.
Optional gears near the assisting hand
The tools that you use less frequently should be kept at you assisting hand side which is not your dominant hand.
Wear your size
Some tool belts are adjustable while others come in different sizes. Choose your size wisely because anything does not fit you well, slightly loose or slightly tight will leave you sore in the long run and an electricians job is intricate as it is. A tool belt should be there to help you out.
Use a Suspender
If you are someone constantly working with heavy tools your back may ache from carrying weight on your waist only, using a suspender will help you in this case.
The tool belts are an absolute necessity for certain jobs like the electricians, where constant change of tools in hand and their simultaneous use takes place at the same time, how it can help you as an assistant in the job depends on its quality, the best tool belt will lessen your burden of picking up the tool from the ground every time. It shall secure the tools in your climb to an electric pole or a construction site. So do read the article well and choose the best tool belt as your partner.
The best tool belt accentuates the electrician’s life enabling him to work in any environment, whether it is a construction site with the rough and clumsy environment or a long vertical climb to the transformer. An electrician’s job varies in such wide range that the image that job initially offers is a smart tool belt wrapped around the waist weighted down with the gears of heavy utility. The best tool belt adds to the description and sustains a professional life.