No matter what, either to improve the perfection of the result or to increase the accuracy of the work, you may need to disassemble any component from a circuit board. With the best De-Soldering Tool, you can easily remove the solder of the components to free up them.
These tools remove the solder properly so that you can easily pick up the component and will be able to solder another component at the same place. In this article, you will get a complete review of some of them.
Basics of a De-Soldering Tool?
The basics of de-solder are the vacuum pressure that is created by the handle. When the handle is pressed it removes all the air inside the tube. When the release button is pressed it creates a vacuum inside the tube that’s why the solder is sucked to the tube.
The solder is melted with the help of a solder machine or any hot tool. The melted solder will remain inside the tube that is cleared later.
Our Recommended Best De-Soldering Tool
There may be a lot od De-soldering pump but you should choose the one that is perfect for your work. Here reviews of some of the best De-soldering pump is given below.
1. Tabiger Solder Wick & De-Soldering Pump
Tabiger Solder Wick & De-soldering Pump is a One-Handed de-soldering tool with power sucking and can be used with both hands. By just pressing the trigger button, you will be able to suck the soldering in an attempt.
It has 2 solder braid with perfect width and length that ensure the proper and full suction of the soldering pest. They are made of copper so that they will not make any effect on the circuit board.
The body of the pump is cover of the high-quality non-slip sponge so that you will be able to hold the de-solder properly. The nozzle is made of nylon so the soldering will not be stuck at the nozzle and even at high temperature, the nozzle will not be bend.
You will also get two solder wicks with the de-solder pump. The de-solder wick is useful for the low amount of solder where the de-solder pump can be used for a large amount.
The problem is the release button is hard to push so that it will be tough to release the pump easily. The solder wick given with the kit is not high quality as they are not as thick as it should be.
2. OMorc De-Soldering Wick, Solder Sucker
OMorc De-soldering Wick, Solder Sucker has the top-notch quality and it is a strong and powerful tool. The body of the sucker is made of aluminum bronze frame and the high-pressure vacuum will ensure the effective removal of the solder from any surface.
The solder sucker has a plastic back to support the frame of the body that ensures the stability and durability of the tool. The tool is very lightweight and properly sized so that you can easily use this on small or big electronics board. The tool can be used by one-handed, no matter right or left.
The compact design will help you to do these tasks with comfort. There is a button on the top by which you can easily release the pump to suck the solder when they are hot.
You will also get one solder wick with the package that is helpful for de-soldering. They remove the soldering properly and left nothing at the board so that your works will be more perfect by using these. The given wicks are of high quality and proper size.
The problem is the body is not affected by high temperature, but the handle and the rubber meltdown due to temperature and the tool become damaged.
3. Engineer SS-02 Solder Sucker
Engineer SS-02 Solder Sucker is a brand product with high quality and will designing look. The body of the tool is fully made of metal that ensure the long-term durability of the product and also for effective performance.
With one-handed plunger operation, it will help you to suck the melted solder properly. It has a self-cleaning facility so that you do not need cleaning the nozzle manually after sucking the solder and this also ensures the proper solder sucking every time you use the tool.
The nozzle is elastic and heats resistance so that it will not be damaged due to high temperature. It will stick to the soldering iron on the board and will suck the solder powerfully so that no solder will be left on the board.
You will also get a spare nozzle with the package so that you can use the tool for a long time even in case the nozzle is bent or damaged. The frame of the body is capable to adjust with high pressure.
The problem is most of the time the silicon tip at the top become jammed that will hamper your flow of work. The metal section of the tool can’t be cleaned properly with the self-cleaning system.
4. Velleman VTDESOL3U Vacuum De-soldering Pump
Velleman VTDESOL3U Vacuum De-soldering Pump is an amazing tool with a heater to suck and de-solder any soldering on the board easily. It is a one-handed operating tool and can be used with any of the right or left hand.
The tool is a compact package with a heater so that you don’t need any other tool or soldering machine to heat the solder of the components. The heater is powerful to melt any kind of solder.
The heater will perfectly heat the solder that ensures the proper melting so that the de-solder can easily suck the melted solder. These ensure the effective disassembling of any component.
The tool can clean the circuit board properly and usable for any kind of component whatever the size is. the cleaning process of the tube also easy so that you will be able to use the de-solder pump for a long time.
The problem of the tool is you can’t remove the pump from the heater as they are joined together in one frame.
5. Hakko FR300-05/P De-soldering Tool
Hakko FR300-05/P De-soldering Tool is a modern de-soldering pump with well-designed and a lot of features. It is very flexible to use and the tool will make your tasks easier and comfortable.
The tool has a built-in heating function so that you do not need any other extra tool to heat the solder to melt it down. The heater is very good and can melt the solder properly with perfect heat.
There is a switch to ON/ OFF the de-soldering pump. When you pressed the button, the gun sucks the melted solder so that you do not need to press any trigger button to release and not to press the handle for reuse.
Maintenance is very easy for the de-solder gun. The shape of the tool is also convenient to use it in any kind of condition. Another advantage is that you can easily adjust the heat of the de-solder gun according to your need to have the effective disassembling.
The bad part of the tool is the body is not strong enough as after many time usages, the body may be broken down or being bend due to pressure and temperature.
6. ECG J-045-DS Electric Corded De-Soldering Iron
ECG J-045-DS Electric Corded De-Soldering Iron is a powerful tool to de-solder any component from a circuit board. It is a compact package of a heater and a sucker so that you can get the solder to melt it down and suck them at a time.
The heater of the tool is very powerful so that it will heat up the solder very quickly. You just need to press the sucker pump to suck the melted solder that will be collected by the tip of the heater.
The tip of the tool is made of metal so that it will not be damaged even in very high temperature. The tool has a rubber grip to hold the tool perfectly. You can easily use the tool by one hand.
The problem is the tip is made of not good quality material as they may be broken after some uses. Again, it is hard to clear the pump as the melted solder is collected in the same tube from where the hot air is out.
7. Teenitor Solder Sucker De-Soldering Vacuum Pump
Teenitor Solder Sucker De-Soldering Vacuum Pump is an amazing tool with which you can easily suck the solder to disassemble any component or IC from your circuit board. It is a small tool so that they are perfect for tiny components and boards.
They have a good bit of suction that is powerful and accurate. They are very easy to use and operate. You need just one hand to hold the tool perfectly and only your thumb to reset and suck by pressing the button. It is lightweight and compact so that you can use it with comfort.
The tool is the very sturdy and perfect tool to remove and clean the melted existing solder from the circuit board. The nozzle is perfectly sized and the material is capable of high temperature and pressure so that you can use the tool without being damaged by the nozzle.
There is a back frame with the body of the tool to support the tube in case of high pressure. the handle is well positioned and the release button can instantly remove the handle to create a fast vacuum to suck the melted solder properly.
The problem with the tool is the size of the de-solder is small as it will be tough to use it in big components and in large circuit boards. You may need to suck the melted several times to clean the solder properly.
8. Tenma 21-8240 Vacuum De-Soldering Iron
Tenma 21-8240 Vacuum De-Soldering Iron is also a two in one pack de-soldering pump that has a built-in heater with the tool. it can heat the solder, melted it down then sucks the melted solder to disassemble the components.
The heating is perfect and it consumed less power. So, it performs effective heating and you do not need any extra tool for this purpose. The suction power is also very good and it can clean by removing all the existing solder from the circuit board.
The body of the tool is made of metal sheet so that the high temperature and the high pressure will not affect the tool. The tool is quick, accurate and effective for de-soldering.
The problem is the release button is too far from the tip so that it will be hard to use the tool by one hand easily.
9. GBSTORE Blue 13” Sucking
GBSTORE Blue 13” Sucking is a complete tool for any kind of de-soldering in any circuit board or IC. They are necessary for also circuit maintenance, IC disassembly, and printed circuit board de-soldering. These tools are easy to use and accurate.
The tools have an anti-skid design that makes the tool easy to hold and place in the right position to suck the solder properly. The body is made of high-quality material that will perform well in high-pressure condition and in high temperature as well.
The nozzle of the de-solder is perfectly sized and well designed so that in the high temperature of the solder, it will not be bend. The nozzle can suck the solder at a time and properly so you need not suck twice for one particular component or integrated circuit element i.e. IC.
There is a release button that will release the handle properly at a time so that the solder will be sucked at a time by the nozzle. So, can easily clean the body later by disassembly them. The tool is specially made for heavy duty and you can use it with comfort by any of your hand.
The problem of the tool is that the size of the sucker is comparatively large as you may face trouble to use this product for small component or in small boards. So, it’s wise to use this tool where the board is large and well amount of solder needs to be sucked.
Best De-Soldering Tool Buying Guide
You need to ensure some key factors to get the Best De-soldering tool for your works. Here is a buying guide for you.
You need to check the nozzle of the tool. They need to be made of high-quality material so that they will not be damaged due to high temperature. They also need to be well designed for high pressure. If you are going to work with the large amount then the nozzle diameter needs to be big otherwise small diameter is needed.
The tool should make enough pressure inside to suck the solder properly. This solder also needs to stay inside so that it will not ruin the circuit board.
The body of the tool should be airtight and the frame should be strong enough to manage the high pressure that is created by the tool to suck the solder. There should be a facility of self-cleaning the solder that is sucked the
The handle of the tool should be strong and the spring also needs to be designed well to reset the handle properly that is important to suck the solder from the circuit board. Again, the release button should release the handle within seconds when they are pressed.
How to Use De-soldering Tool/Pump
To remove the solder properly you need to follow the steps very carefully. At first look on the component that you want to disassemble from the circuit board and then heat the solder of that component so that the solder will be melted down.
Then by holding the sucker properly, press the handle and place the sucker on the solder that you want to suck. Press the release button, the handle will be released and the pump will suck the solder so that you can now disassemble the component easily.
You can use solder wick to clean the area properly and also to ensure that there will be no solder left on the circuit board.
Frequently Asked Questions (FAQs)
There may arrive a lot of questions on your mind about the Best De-Soldering Tool. Here some of the Frequently Asked Questions and their answers that might be helpful for you.
Q. How to suck the little-melted solder from the circuit board?
Ans: Use a solder wick to remove a small amount of solder.
Q. What to do if the handle is stuck?
Ans: If you can’t release the handle by pressing the release button, then open the body of the tool and release the spring. Also, check the button is okay or not.
Q. Will the high heat be a problem for the de-soldering tool?
Ans: Normally the tools are made of high-quality material that is heat resistant. The nozzles are capable of working in high-temperature condition. But if they are damaged, then you need to change the nozzle or the frame.
De-soldering is an important part of circuit board making as you need to disassemble any component and IC anytime. With the Best De-Solder Tool, you will be able to easily do these tasks in a short time and perfectly. But the safety should be considered as the most prior thing in these kinds of works.